Docs › Images › Filters: color, light and FX
Filters: color, light and FX
Filters is Develop's tools on the selected layer, in five tabs: Color, Light, Develop, FX and Style.
- Color has Base, Curves, HSL, Wheels and Mixer.
- Its Base holds Temp, Tint, Vibrance and Saturation. Double-click a slider to put it back.
- Light has Base, Curve, Levels and Detail. Curve and Levels show the picture's values for the channel you pick: the layer's before its grade, or on an adjustment layer everything below it.
- Exposure is in Light's Base, with Offset, Contrast, Highlights, Shadows, Whites, Blacks and Dehaze.
- A dot on a tab means it holds settings. Right-click a tab to clear just that tab, or a sub-tab such as Curve to clear only that.
- The eyedropper picks from the canvas: in HSL it chooses the band of the color you click. Esc cancels.
- Develop opens Develop's whole editor over the app, on this layer.
- FX has Blur, Motion blur, Vignette, Sharpen, Glow, Halation, Grain, Fringing, Noise reduction and JPEG repair, each with its own switch. A dot marks the ones that are on, and off keeps their settings. Vignette's Guides show it on the picture: drag the dot to move it, a ring to set its edge, or a square on the dashed ring to scale it. Its Falloff and Displacement shape the edge the same way as Area's.
- Grain's Amount goes to 10 on the second half of its slider, getting heavier without clipping. Its Break-up is the one in Develop and Automations: the picture breaks into grains, and detail finer than a grain dissolves. At 0 the grain lies on top.
- Blur has Lens, Radial, Zoom and Area, each with its own switch. Lens focuses by Tilt-shift or a Depth map, from Build depth map (on your device), Upload or Generate (Generative AI, for members).
- Radial spins the picture around a center, and Zoom streaks it out from one while its shape stays sharp. Click the picture to place the center, and drag the handle to size it.
- Area blurs along lines you draw, by its Amount, Width and Edge softness; Falloff sets how fast the blur comes in across the fade (Fast to Slow), and Displacement lets the picture's light and dark change that speed place by place: turned up, light parts fade slower and dark parts faster, until parts of the fade are cut away. Turn on Draw, under the settings, and click the picture to add points (Done at the foot of the canvas, or Esc, stops drawing); drag one to move it, double-click it to take it away, right-click it (press and hold on a touch screen) to Delete point or reset its strength or spread, and press Return to end a line. At an Edge softness of 1 the blur fades from the line to the edge of Width; above 1, up to 30, the fade runs that many times as far.
- Each point is a square, and its size is its Strength: drag a corner or an edge to scale it, from 0 up to 10 times the Amount. A bigger square is more blur. Drag the inside to move the point.
- A point you click also shows its Spread, up to 30 times Width: drag the small square out on its line, or in, to widen or narrow the blur there.
- Motion blur has Motion path, Light trails and Highlights. Whole layer streaks it all one way, by its Amount and Direction; it starts off, so only what you draw moves until you switch it on.
- Under Paths, right below the switch, Draw a line and the streaks follow it, or Erase where nothing should move. For Light trails, draw from a light to where it went; a click near a trail adds another light.
- Highlights streaks every small light in the picture at once, with nothing to draw. Linear runs every streak one way, by Direction; Radial runs them out from a center (Place center, then click the picture). Threshold sets how bright a light must be, and Point size how big it can be: a lamp or a lit window streaks, a bright wall or sky doesn't (at 1, anything bright does). Length, Brightness and Fade shape the streaks.
- Every effect but Vignette, Area and Light trails has a Mask at the foot of its settings. Switch it on and an oval goes on the picture: the effect applies inside it and fades out across its edge. Pick Oval, Rectangle, Band or Draw (drag an outline on the picture). Drag a point to move it, press the outline to add one, right-click a point (press and hold on a touch screen) to Delete point or make it a corner, and drag the square in the middle to move the whole shape.
- Edge softness sets how wide the fade is, Falloff and Displacement shape it as Area's do, and Invert puts the effect outside the shape. Lens blurs less toward the edge rather than fading out. Each effect has its own mask; on an iPad or a phone a layer can have three.
- Style has Relight, Film damage, Pixel Art, LED and ASCII, the same filters as Automations, each with its own switch. A dot marks the ones that are on, and off keeps their settings. Right-click Style to clear them. On an adjustment layer they style everything below it.
- Relight lights a photo again from a light you place. Turn it on and Images finds the photo's shape on your device (the first time, it downloads the depth model, about 100 MB). Drag the light on the pad, which shows that shape, or press Place on picture and click the canvas. Height, Brightness, Reach, Softness and the color set the light. Darken the rest dims the photo's own light so the new one leads, Shadows adds shadows cast by what stands in its way, and Shine adds a glint. Depth, Detail and Smooth set how much shape the light finds. Under Light only, Pick an object (then click it) or Use selection lights just that thing and leaves the rest as it was; Whole picture goes back. Relight adds light and shade; it can't take away a hard shadow already in the photo. It runs before the other Style filters.
- Reset clears the layer's Color and Light, and what Develop added. FX and Style keep their filters: right-click FX or Style to clear them.
- A layer with Filters on shows a green square on its picture in Layers, and Filters on the rail has one while the layer is selected; click the square to come back here.
Develop
It covers Looks, Auto, Denoise, Mask, Dodge & Burn, Face, its own layers, Light and Color. The pixels aren't changed: Done applies it as one undo step, Cancel leaves the layer as it was, and reopening brings your settings back.
The whole picture
An Adjustment layer (New Layer › Adjustment) has the same Color, Light, FX and Style tabs (not Develop), working on everything below it without touching a layer. On a phone, add one from Layers, beside +.